4.2.4

Topic 16

Resistance

  • IGCSE Physics 0625
  • 2 min read
  • Syllabus 2026, 2027 and 2028

Core

  1. 1

    Recall and use the equation for resistance

  2. 2

    Describe an experiment to determine resistance using a voltmeter and an ammeter and do the appropriate calculations

  3. 3

    State, qualitatively, the relationship of the resistance of a metallic wire to its length and to its cross-sectional area

Supplement

  1. 4

    Sketch and explain the current–voltage graphs for a resistor of constant resistance, a filament lamp and a diode

  2. 5

    Recall and use the following relationship for a metallic electrical conductor:

    • aresistance is directly proportional to length
    • bresistance is inversely proportional to cross-sectional area

Cambridge IGCSE Physics 0625 syllabus 2026-2028, 4.2.4 Resistance (copied for internal use as permitted by Cambridge)

Detailed · Deep study

1Resistance

Resistance opposes the current. For a given p.d., a larger resistance gives a smaller current.

Resistance is measured in ohms (Ω).

Worked example

Resistance

A current of 0.40 A flows through a resistor when the p.d. across it is 6.0 V. Find its resistance.

  1. 1

    R = V ÷ I.

Answer15 Ω

Fig. 1Determining resistance.

Practical

Measuring resistance

Aim. To determine the resistance of a resistor (or a length of wire).

Method

  1. Set up the circuit with the ammeter in series and the voltmeter in parallel across the resistor.
  2. Adjust the variable resistor to obtain different currents; record V and I each time.
  3. Calculate R = V ÷ I for each pair and find the mean (or plot V against I: the gradient is R).
independent variablecurrent (set by the variable resistor)
dependent variablep.d.
controlled variabletemperature of the resistor

Results. For an ordinary resistor at constant temperature R is the same for every pair of readings.

Safety. Switch off between readings so the wire does not heat up.

2Length and thickness of a wire

  • A longer wire has a greater resistance – electrons have further to travel through the lattice.
  • A wire with a larger cross-sectional area (thicker) has a smaller resistance – there are more paths for the electrons.

Worked example

Proportional reasoning

(Supplement) A wire 2.0 m long has a resistance of 6.0 Ω. What is the resistance of a 3.0 m wire of the same material with twice the cross-sectional area?

  1. 1

    Length × 1.5.

  2. 2

    Area × 2 halves R.

Answer4.5 Ω

3Current–voltage graphs (Supplement)

Fig. 2I–V characteristics.
  • Resistor (constant resistance): a straight line through the origin – current is proportional to p.d. (Ohm's law).
  • Filament lamp: a curve that gets less steep – as the current increases, the filament gets hotter and its resistance increases.
  • Diode: current flows in one direction only; in the reverse direction its resistance is very high and the current is (almost) zero.

4Exam focus

Key words: R = V/I; ohm; voltmeter in parallel, ammeter in series; longer → more resistance; thicker → less resistance; proportional to length; inversely proportional to area; filament heats up; diode one direction.

Quick self-check

Answer in your head first, then reveal.

  1. 3.0 ÷ 12 (1) = 0.25 A (1).

  2. Longer – greater resistance (1); thicker – smaller resistance (1).

  3. Curve / gradient decreases (1); filament gets hotter so resistance increases (1).

Finished this subtopic? Track it on your subject page.