6.2

Topic 8

Rate of reaction

  • IGCSE Chemistry 0620
  • 5 min read
  • Syllabus 2026, 2027 and 2028

Core

  1. 1

    Describe the effect on the rate of reaction of:

    • achanging the concentration of solutions
    • bchanging the pressure of gases
    • cchanging the surface area of solids
    • dchanging the temperature
    • eadding or removing a catalyst, including enzymes
  2. 2

    State that a catalyst increases the rate of a reaction and is unchanged at the end of a reaction

  3. 3

    Describe practical methods for investigating the rate of a reaction including change in mass of a reactant or a product and the formation of a gas

  4. 4

    Interpret data, including graphs, from rate of reaction experiments

Supplement

  1. 5

    Describe collision theory in terms of:

    • anumber of particles per unit volume
    • bfrequency of collisions between particles
    • ckinetic energy of particles
    • dactivation energy,
  2. 6

    Describe and explain the effect on the rate of reaction of the following, using collision theory:

    • achanging the concentration of solutions
    • bchanging the pressure of gases
    • cchanging the surface area of solids
    • dchanging the temperature
    • eadding or removing a catalyst, including enzymes
  3. 7

    State that a catalyst decreases the activation energy, , of a reaction

  4. 8

    Evaluate practical methods for investigating the rate of a reaction including change in mass of a reactant or a product and the formation of a gas

Cambridge IGCSE Chemistry 0620 syllabus 2026-2028, 6.2 Rate of reaction (copied for internal use as permitted by Cambridge)

Detailed · Deep study

1Rate of reaction

The rate of reaction measures how quickly a reactant is used up or a product is formed. It can be measured as the change in amount (mass, volume or concentration) per unit time, for example cm³ of gas per second.

2Collision theory (Supplement)

  • For a reaction to happen, reactant particles must collide.
  • Only collisions with energy at least equal to the activation energy, , are successful (lead to reaction).
  • The rate depends on the frequency of collisions (how many per second) and on the proportion that have enough energy.
  • Frequency depends on the number of particles per unit volume and on how fast the particles move (their kinetic energy).
Fig. 1More particles per unit volume give more frequent collisions.
Activation energy, Syllabus definition

the minimum energy that colliding particles must have to react

3Factors affecting rate

ChangeEffect on rateExplanation (collision theory – Supplement)
increase concentration of a solutionfastermore particles per unit volume → more frequent collisions
increase pressure of a gasfastergas particles closer together: more particles per unit volume → more frequent collisions
increase surface area (smaller pieces / powder)fastermore particles exposed at the surface → more frequent collisions
increase temperaturefasterparticles have more kinetic energy: they move faster, so collisions are more frequent, and a greater proportion of collisions have energy ≥ – more successful collisions
add a catalyst (or enzyme)fasterprovides an alternative pathway with a lower activation energy, so more collisions are successful

Catalysts and enzymes

A catalyst increases the rate of a reaction and is unchanged (chemically, and in mass) at the end. Only a small amount is needed and it can be reused. Examples: iron in the Haber process, manganese(IV) oxide in the decomposition of hydrogen peroxide.

Enzymes are proteins that act as biological catalysts. They work best at an optimum temperature (often about 37 °C) and pH; at high temperatures they are denatured and stop working.

Fig. 2The catalysed route has a lower activation energy.

Explaining the effect of temperature (Supplement)

Raising the temperature has two effects: particles move faster, so they collide more often; and more importantly, they have more kinetic energy, so a greater proportion of collisions have energy equal to or greater than . This is why a small rise in temperature can increase the rate a lot.

4Investigating rate in practice

Fig. 3Two common methods.
  • Volume of gas: collect the gas in a gas syringe (or an upturned measuring cylinder over water) and read the volume at regular intervals.
  • Change in mass: place the flask on a balance and record the mass at regular intervals as gas escapes.
  • Disappearing cross / precipitate: for sodium thiosulfate + acid, time how long it takes for a cross under the flask to be hidden by the sulfur precipitate; rate ∝ 1/time.

Practical

Effect of concentration on the rate of reaction of marble chips with acid

Aim. To find how the concentration of hydrochloric acid affects the rate of its reaction with calcium carbonate.

Method

  1. Place a known mass of marble chips (same size) in a conical flask.
  2. Add a measured volume of hydrochloric acid of known concentration, quickly insert the bung connected to a gas syringe and start the stopwatch.
  3. Record the volume of gas every 30 s until no more gas is produced.
  4. Repeat with different concentrations of acid, keeping everything else the same.
independent variableconcentration of hydrochloric acid
dependent variablevolume of carbon dioxide produced over time
controlled variablemass and size of marble chips; volume of acid; temperature

Results. Plot volume of gas against time. The higher the concentration, the steeper the initial gradient.

Safety. Wear eye protection; hydrochloric acid is an irritant.

Evaluating the methods (Supplement)

MethodStrengthsLimitations
gas syringeaccurate volume readings; gas collected directlysome gas escapes before the bung is inserted; the plunger can stick; limited volume (usually 100 cm³)
upturned measuring cylinder over watercheap and simplenot suitable for gases that dissolve in water (e.g. ammonia, some CO₂ dissolves); harder to read precisely
mass loss on a balanceeasy to take many readings; no gas is lost from the measurementunsuitable for light gases such as hydrogen (mass change too small); needs a sensitive balance; cotton wool needed to stop acid spray

5Interpreting rate graphs

Fig. 4Interpreting volume–time graphs.
  • The gradient of the line at any point is the rate at that time.
  • The line is steepest at the start, when the reactants are most concentrated.
  • The gradient decreases as reactants are used up; when the line becomes horizontal the reaction has stopped (the limiting reactant is used up).
  • A faster reaction has a steeper initial gradient and levels off sooner.
  • The final volume depends only on the amount of limiting reactant, not on the rate.

6Exam focus

Key words: more frequent collisions; particles per unit volume; kinetic energy; activation energy; greater proportion of successful collisions; catalyst unchanged; alternative pathway with lower ; gradient; levels off.

Quick self-check

Answer in your head first, then reveal.

  1. Rate increases (1).

  2. Increases rate (1); unchanged at the end of the reaction (1).

  3. Collect gas in a gas syringe (1); measure volume at regular time intervals (1).

  4. Particles have more kinetic energy / move faster (1); more frequent collisions (1); greater proportion of collisions have energy ≥ activation energy (1).

  5. Provides an alternative pathway (1); with lower activation energy, so more collisions are successful (1).

  6. Hydrogen is produced, which has a very low mass / density (1); the change in mass would be too small to measure accurately (1).

Finished this subtopic? Track it on your subject page.