12.4

Topic 20

Separation and purification

  • IGCSE Chemistry 0620
  • 3 min read
  • Syllabus 2026, 2027 and 2028

Core

  1. 1

    Describe and explain methods of separation and purification using:

    • aa suitable solvent
    • bfiltration
    • ccrystallisation
    • dsimple distillation
    • efractional distillation
  2. 2

    Suggest suitable separation and purification techniques, given information about the substances involved

  3. 3

    Identify substances and assess their purity using melting point and boiling point information

Cambridge IGCSE Chemistry 0620 syllabus 2026-2028, 12.4 Separation and purification (copied for internal use as permitted by Cambridge)

Detailed · Deep study

1Methods of separation and purification

MethodSeparatesExample
dissolving in a suitable solventa soluble solid from an insoluble one (then filter)salt from sand (water); sulfur from sand (a non-aqueous solvent)
filtrationan insoluble solid from a liquidsand from water; excess solid in salt preparation
crystallisationa dissolved solid from its solutioncopper(II) sulfate crystals from solution
simple distillationa solvent (liquid) from a dissolved solidpure water from sea water
fractional distillationmiscible liquids with different boiling pointsethanol from water; petroleum fractions; gases from liquid air

Using a solvent and filtration

To separate a mixture of two solids, choose a solvent that dissolves only one of them. Stir, then filter: the insoluble solid stays on the filter paper as the residue, and the solution passes through as the filtrate. Wash the residue with a little solvent and dry it.

Crystallisation

Heat the solution to evaporate some solvent until it is saturated (the point of crystallisation – crystals form on a cold glass rod). Leave it to cool: the solute is less soluble when cold, so crystals form. Filter off the crystals, wash with a little cold solvent and dry them.

See Topic 7 · Chemical EnergeticsCrystallisation in making salts: 7.3.

Simple distillation

Fig. 1Simple distillation apparatus.

The solution is heated; the solvent boils, the vapour passes into the condenser, where it is cooled and condenses, and the pure liquid (distillate) is collected. The dissolved solid remains in the flask. The thermometer bulb is level with the side arm to measure the temperature of the vapour leaving; cold water enters the condenser at the bottom so it fills completely.

Fractional distillation

Fig. 2Fractional distillation apparatus.

Used for miscible liquids (they mix completely) with different boiling points, such as ethanol (78 °C) and water (100 °C). The vapour rises up a fractionating column packed with glass beads, which provides a large surface for repeated condensation and evaporation. The liquid with the lower boiling point reaches the top first and distils over; the thermometer stays at its boiling point until it has all been collected, then rises.

See Topic 11 · Acids and BasesFractional distillation of petroleum: 11.3.

2Suggesting a method

Use the information given about the substances: state, solubility, boiling point.

Information givenSuitable technique
one solid soluble, the other insoluble in wateradd water, stir, filter; evaporate / crystallise the filtrate
want the solid from a solutioncrystallisation (or evaporation if the solid does not decompose)
want the liquid from a solutionsimple distillation
two liquids that mix, different boiling pointsfractional distillation
mixture of coloured soluble substanceschromatography (12.3)

3Identifying substances and assessing purity

Every pure substance has a fixed, sharp melting point and boiling point, so these can identify a substance by comparison with data. Pure water melts at 0 °C and boils at 100 °C.

ObservationConclusion
melts sharply at the data-book valuepure substance; identity confirmed
melts over a range of temperatures, below the data valueimpure
boils above the data value / over a rangeimpure (contains dissolved impurities)

Purity matters for food and drugs – impurities could be harmful.

4Exam focus

Key words: suitable solvent; filtration; residue; filtrate; crystallisation; saturated; simple distillation; condenser; distillate; fractional distillation; miscible; different boiling points; sharp melting point.

Quick self-check

Answer in your head first, then reveal.

  1. Add water and stir to dissolve the salt (1); filter to remove sand (1); heat filtrate to point of crystallisation / evaporate (1); cool and dry crystals (1).

  2. Fractional distillation (1); ethanol and water have different boiling points (1).

  3. To cool the vapour so that it condenses to a liquid (1).

  4. The sample is impure (1); it melts over a range below the pure value (1).

Finished this subtopic? Track it on your subject page.